Fasteners

Industrial Fasteners for Construction, Fabrication & Maintenance

Industrial fasteners are the backbone of mechanical fastening, anchoring, and structural assembly across a wide range of industries. Our comprehensive selection is engineered to meet the rigorous demands of industrial, fleet, and maintenance, repair, and operations (MRO) applications. Whether you require metric or standard sizes, our fasteners ensure compatibility and consistent sizing for seamless repair, replacement, and new installations. From heavy-duty construction projects to precision fabrication and ongoing equipment service, our hardware solutions support every phase of your operation. Explore a broad inventory designed for structural integrity, mechanical reliability, and secure anchoring—empowering your team to work efficiently and safely, no matter the jobsite or application.

Bolts, Screws & Threaded Rod

Discover our extensive range of bolts, screws, and threaded rod, available in both standard and metric dimensions. These essential fasteners provide reliable mechanical connections for structural assembly, equipment installation, and repair. For more details, visit our Bolts, Screws & Threaded Rod category.

Nuts, Washers & Locking Hardware

Ensure secure fastening and load distribution with our selection of nuts, washers, and locking hardware. Designed for compatibility with a variety of bolts and threaded rods, these components are critical for maintaining joint integrity in demanding environments. Explore the full range in our Nuts, Washers & Locking Hardware section.

Anchors & Threaded Inserts

Achieve dependable anchoring in concrete, masonry, and other substrates with our anchors and threaded inserts. These solutions are ideal for structural and mechanical applications where secure, long-lasting fastening is required. Learn more in our Anchors & Threaded Inserts category.

Pins, Retaining Rings & Rivets

For applications requiring precise alignment, retention, or permanent assembly, our pins, retaining rings, and rivets deliver consistent performance. These specialty fasteners are essential for equipment maintenance, fabrication, and assembly tasks. Visit our Pins, Retaining Rings & Rivets page for more information.

Specialty Fasteners & Hardware

Address unique fastening challenges with our specialty fasteners and hardware, including tamper-resistant, high-strength, and application-specific solutions. Support your fabrication, installation, and service needs with products engineered for reliability and ease of use. Browse our Specialty Fasteners & Hardware category for tailored options.

Value Propositions

Broad selection of standard and metric fasteners for every application
Suitable for industrial, fleet, and maintenance use
Structural, mechanical, and anchoring solutions for diverse environments
Consistent sizing for efficient repair and replacement
Supports fabrication, installation, and equipment service

Display items per page

SHEET METAL SCREW HEX WASH HD #6 X 3/8"

6X38H

A thread forming tapping screw with spaced threads and a gimlet point.
For self starting in thin metal or resin-filled plywood.
Has an indented top surface, six flat sides with a flat washer which projects beyond the sides and provides a flat bearing surface.
The washer and head are formed together as one piece. (Hex washer slotted head)
Increased bearing area reduces likelihood of crushing mating surfaces.
Zinc plated steel.
Screw diameter 6
Screw length 3/8 inch

$10.40
$0.104

+ -

SHEET METAL SCREW OVAL PHIL HD #6 X 3/8" STAINLESS

6X38OP

A thread forming stainless tapping screw with spaced threads and a gimlet point.
For self starting in thin metal or resin-filled plywood.
A countersunk head with a rounded top surface and a cone-shaped bearing surface.
Preferred over a flat head in conical applications, or when a more decorative finished look is desired.
The countersunk surface nests into mating countersunk application sites.
Oval head, phillips drive
Screw diameter 6
Screw length 3/8 inch

$15.00
$0.15

+ -

SHEET METAL SCREW PHIL PAN HD #6 X 3/8"

6X38P

A thread forming tapping screw with spaced threads and a gimlet point.
For self starting in thin metal or resin-filled plywood.
Phillips Pan Head
For general applications.
Can be substituted in most applications for round, truss or binding screws.
Steel zinc plated.
Diameter: 6
Length: 3/8"

$6.40
$0.064

+ -

HEX CAP SCREW BOLT METRIC ZINC M6-1.0 X 40, CL 8.8

6X40M

Hex head cap screw with metric thread pitch made from medium carbon steel.
Heat treated.
Tensile strength: 800 Newtons/mm² minimum.
Zinc plated.
Metric coarse threads.
Diameter: M6-1.0.
Length: 40 mm.

$28.77
$0.2877

+ -

HEX CAP SCREW BOLT METRIC ZINC M6-1.0 X 45, CL 8.8

6X45M

Hex head cap screw with metric thread pitch made from medium carbon steel.
Heat treated.
Tensile strength: 800 Newtons/mm² minimum.
Zinc plated.
Metric coarse threads.
Diameter: M6-1.0.
Length: 45 mm.

$29.64
$0.2964

+ -

HEX CAP SCREW BOLT METRIC ZINC M6-1.0 X 50, CL 8.8

6X50M

Hex head cap screw with metric thread pitch made from medium carbon steel.
Heat treated.
Tensile strength: 800 Newtons/mm² minimum.
Zinc plated.
Metric coarse threads.
Diameter: M6-1.0.
Length: 50 mm.

$31.02
$0.3102

+ -

ROLL PIN - PLAIN FINISH 7/32" X 2"

7322RP

Standard single-turned pin with a longitudinal slot and chamfered ends to facilitate installation.
Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
Usage is limited only by your imagination and technological capabilities.
Spring pins require only a straight drilled hole and may be installed using automatic equipment.
Reusable.
Carbon steel, plain finish material
Diameter is 7/32
Length is 2 inches

$55.86
$1.1172

+ -

ROLL PIN - PLAIN FINISH 7/32" X 1"

7321RP

Standard single-turned pin with a longitudinal slot and chamfered ends to facilitate installation.
Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
Usage is limited only by your imagination and technological capabilities.
Spring pins require only a straight drilled hole and may be installed using automatic equipment.
Reusable.
Carbon steel, plain finish material
Diameter is 7/32
Length is 1 inch

$19.635
$0.3927

+ -

ROLL PIN - PLAIN FINISH 7/32" X 3/4"

73234RP

Standard single-turned pin with a longitudinal slot and chamfered ends to facilitate installation.
Used as locking devices, positioning points, anti-chafing surfaces, shaft, or sleeves for wiring.
Usage is limited only by your imagination and technological capabilities.
Spring pins require only a straight drilled hole and may be installed using automatic equipment.
Reusable.
Carbon steel, plain finish material
Diameter is 7/32
Length is 3/4 inch

$16.98
$0.3396

+ -

CLEVIS PIN - ADJUSTABLE PLAIN 7/16" DIA. 2-1/2" LONG

76212ACP

A quick replacement pin.
Feature a series of holes making it adaptable to varying lengths.
Easily replaces bolts, cotter pins or rivets on all types of equipment.
Use the diameter that fits your application and cut off the excess length.
Plain finish.
Diameter: 7/16".
Length: 2-1/2".

$22.997
$2.2997

+ -

HEX CAP SCREW BOLT UNC ZINC 7/16"-14 X 1-1/2", GR 5

76X112C

Made from medium carbon steel.
Heat treated.
Tensile strength: 120,000 psi. minimum.
Zinc plated.
Unified screw threads :UNC.
Diameter: 7/16"-14.
Length: 1-1/2".

$54.505
$1.0901

+ -

COTTER PIN - ZINC 7/64" X 1-1/2"

764X112CP

Metal, extended prong type cotter pin.
Extended prong makes separating the tines easier.
Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
When used with castle or slotted nuts, it becomes a safety locking device.
Low carbon steel, zinc plated material
Diameter is 7/64 inch
Length is 1-1/2 inches

$34.92
$0.3492

+ -

COTTER PIN - ZINC 7/64" X 3/4"

764X34CP

Metal, extended prong type cotter pin.
Extended prong makes separating the tines easier.
Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
When used with castle or slotted nuts, it becomes a safety locking device.
Low carbon steel, zinc plated material
Diameter is 7/64 inch
Length is 3/4 inch

$27.84
$0.2784

+ -

HEX CAP SCREW BOLT UNC ZINC 7/16"-14 X 1-1/2", GR 8

76X112C8

Made from medium carbon alloy steel.
Heat treated.
Tensile strength: 150,000 psi. minimum.
Yellow zinc plated.
Unified screw threads :UNC.
Diameter: 7/16"-14.
Length: 1-1/2".

$47.30
$0.946

+ -

COTTER PIN - ZINC 7/64" X 2"

764X2CP

Metal, extended prong type cotter pin.
Extended prong makes separating the tines easier.
Used to anchor various assemblies by insertion into a drilled hole of a shaft or pin and spreading the points to hold the assembly in position.
When used with castle or slotted nuts, it becomes a safety locking device.
Low carbon steel, zinc plated material
Diameter is 7/64 inch
Length is 2 inches

$41.60
$0.416

+ -